濟南飼料機械廠
聯系人：安經理
手機：152-5313-4653
郵箱：347299818@qq.com
地址：濟南市濟北開發區
1、為避免機器在運輸、裝卸等環節中出現意外，使用前必須檢查各部位螺栓、螺母是否松動，扁齒，圓齒，主軸螺母有無松動現象。用手轉動皮帶輪，檢查機器有無碰撞現象。
To avoid unexpected machine in the transport, handling and other sectors in various parts of the bolts must be checked before use, the nut is loose, flat teeth, round teeth, spindle nut without loosening. Rotate the pulley, check the machine whether the collision phenomenon.
2、機器轉動是否靈活，機內是否有雜物，開機空轉3分鐘，無異常現象，才能開始操作。
Turn the machine is flexible, if there is debris inside the machine, turn idle 3 minutes, no abnormal phenomenon, to begin operation.
3、工作時一定要注意清除物料中的雜物，嚴禁鐵塊石頭等物進入機器，以免損機傷人，接料布袋應有4米以上長度，直徑0.6米，布料不能過密，使用中要及時出料，保證布袋有足夠的透氣性。
Work must pay attention to remove material in the debris, stones and other objects prohibited iron into the machine, so as not to damage machine wounding, then there should be four meters above material bag length, 0.6 meters in diameter, the fabric is not too close, use should be promptly the material to ensure that the bag has sufficient permeability.
4、喂料要均勻，注意動力的負荷程度，免以噎住。粉碎顆粒物時可用抽板調節器節喂入量，當一角磨損影響工作效率時，可將錘片反面調頭(調頭時4組一次一起調，以免引起轉子不平衡)更換錘片應全部更換。
Feeding should be uniform, pay attention to the extent of the power load, free to choke. When crushed particles available pumping plate section feed rate regulator, when worn affect the efficiency of the iceberg, you can turn around and reverse hammer (a tone when a U-turn four groups together, so as not to cause the rotor unbalance) to replace the hammer should all be replaced.
5、每天開機前應加注黃油，使用500小時應檢查軸承狀況，安裝篩片時有毛刺一面應裝在上面。根據粉碎物料的細度，選擇不同直徑篩孔的篩片。
Before starting the day should bear butter, use 500 hours should check bearing condition, installation piece burr side of the screen should be mounted on top. According to the fineness of the crushed material, choose a different diameter mesh sieve.